HOME   |    PDF   |   


Title

Comparative evaluation of 3D-printed resin endocrowns and CAD/CAM milled ceramic endocrowns in endodontically treated molars

 

Authors

Ritika Satija 1,*, Shallu Maggo 1, Shalini Pandey 2, Arindam Banik 3, Ajimol Theresa Jose 4 & Vikram Karande 5

 

Affiliation

1Department of Conservative Dentistry and Endodontics, Santosh Dental College, Ghaziabad, Uttar Pradesh, India; 2Department of Prosthodontics, ECHS, Namkum Jharkhand, India; 3Department of Conservative Dentistry and Endodontics, Guru Nanak Institute of Dental Sciences and Research, Kolkata, West Bengal, India; 4Department of Prosthodontics, AIMST University, Bedong, Kedah, Malaysia; 5Department of Dentistry, AIIMS, Rajkot, Gujarat, India; *Corresponding author

 

Email

Ritika Satija - E-mail: ritika.satija94@gmail.com
Shallu Maggo - E-mail: shallumaggo21@gmail.com
Shalini Pandey - E-mail: shalini.in.jss@gmail.com
Arindam Banik - E-mail: arindambanik.1993@gmail.com
Ajimol Theresa Jose - E-mail: ajimoltheresa@aimst.edu.my
Vikram Karande - E-mail: drvikramkarande@gmail.com; hoddental@aiimsrajkot.edu.in
 

Article Type

Research Article

 

Date

Received October 1, 2026; Revised October 31, 2026; Accepted October 31, 2026, Published October 31, 2026

 

Abstract

Endodontically treated molars are highly susceptible to fracture and the optimal fabrication method for endocrowns between additive 3D printing and subtractive CAD/CAM milling remains uncertain. This in vitro comparative study evaluated 120 standardized mandibular first molar endocrowns fabricated using 3D-printed resin (n = 60) or CAD/CAM-milled lithium disilicate ceramic (n=60), assessing marginal and internal fit, fracture resistance, micro leakage, color stability and flexural strength. CAD/CAM-milled lithium disilicate endocrowns showed significantly better marginal fit (63.4 +/- 12.1 versus 89.7 +/- 15.3 μm; p < 0.001) and fracture resistance (2847 +/- 312 versus 1964 +/- 278 N; p < 0.001), whereas 3D-printed resin endocrowns showed significantly lower micro leakage (p = 0.01) and better color stability after thermocycling (p = 0.004), with comparable internal fit (p = 0.09). CAD/CAM-milled lithium disilicate endocrowns are preferable for posterior teeth subjected to high occlusal loads, while 3D-printed resin endocrowns provide a cost-effective and clinically acceptable alternative with favourable short-term performance. This study advances current knowledge by establishing a comparative evidence-based framework for material selection in endocrown fabrication and supporting future clinical trials to validate these findings under functional conditions.

 

Keywords

Endocrown, 3D-printed endocrown, CAD/CAM ceramic, lithium disilicate, endodontically treated molars, marginal fit, fracture resistance, digital dentistry

 

Citation

Satija et al. Bioinformation 22(10): 6448-6451 (2026)

 

Edited by

Ritik Kashwani

 

ISSN

0973-2063

 

Publisher

Biomedical Informatics

 

License

This is an Open Access article which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly credited. This is distributed under the terms of the Creative Commons Attribution License.